Tuesday, January 31, 2012

Lasco 06-9111 Angle Stop Add-A-Tee Adapter 3/8-Inch Female Compression X 3/8-Inch Compression X 3/8-Inch Compression

Lasco 06-9111 Angle Stop Add-A-Tee Adapter 3/8-Inch Female Compression X 3/8-Inch Compression X 3/8-Inch Compression Review



Lasco 06-9111 Angle Stop Add-A-Tee Adapter 3/8-Inch Female Compression X 3/8-Inch Compression X 3/8-Inch Compression Feature

  • Inlet 3/8" OD female compression x 3/8" OD compression x 3/8" OD compression
  • Install on angle stop
  • Used for adding an outlet
  • Lead free product, meets California AB-1953, Vermont, and new federal standards for low lead applications
  • Rough brass construction
3/8' Female Compression Inlet x 3/8' Compression x 3/8' Compression, Angle Stop Add A Tee, California & Vermont Lead Free Compliant Product, Carded.


Monday, January 30, 2012

1/2" 3-way Elbow PVC Fitting Connector

1/2" 3-way Elbow PVC Fitting Connector Review



1/2" 3-way Elbow PVC Fitting Connector Feature

  • Ideal for creating corners in square PVC applications.
  • Made from impact proof, ultra-premium furniture-grade PVC.
  • Superior, glossy surface finish.
  • UV Stabilized for outdoor color retention.
  • Tapered ends for a clean, transitional appearance.
This is not your standard plumbing-grade PVC fitting. FORMUFIT PVC fittings let you create anything with PVC pipe! This elbow connector joins 1/2" (0.840") PVC pipe at three points on multiple planes for corner joints.


Cash Acme U340A Shark Bite 3/4-by-3/4-Inch FNPT Drop Ear Elbow Push Pipe Fittings Adapter

Cash Acme U340A Shark Bite 3/4-by-3/4-Inch FNPT Drop Ear Elbow Push Pipe Fittings Adapter Review



Cash Acme U340A Shark Bite 3/4-by-3/4-Inch FNPT Drop Ear Elbow Push Pipe Fittings Adapter Feature

  • Easy, quick push-fit connection of water distribution pipe , this item cannot ship to CA or VT
  • Design certified and listed to ASSE 1061/NSF 61
  • Listed by IAPMO and certified for potable and hydronic heating water distribution
  • Certified for underground applications and as a manufactured joint without access panels
  • Meet UPC, IPC and CUPC requirements
3/4'' x 3/4'' drop ear elbow can be used to connect copper, CTS, CPV, and PEX pipe in any combination. Presents a revolutionary solution to connecting water distribution pipe. The fittings are certified for underground applications and as a manufactured joint without access panels. It meets UPC, IPC, and CUPC requirements. Design certified and listed to ASSE 1061/NSF61. The fittings are rated at 200 F., 200 P.S.I. It is made of 1 piece DZR brass, which is noncorrosive, low lead material. Fittings can be buried and placed behind drywall. Fittings are removable and reuseable.


Sunday, January 29, 2012

Genova Products 30155CP 1/2-Inch PVC Pipe Cap, Slip - 10 Pack

Genova Products 30155CP 1/2-Inch PVC Pipe Cap, Slip - 10 Pack Review



Genova Products 30155CP 1/2-Inch PVC Pipe Cap, Slip - 10 Pack Feature

  • Used to cap pipe
  • Conveniently packaged in quantities of 10
  • Ideal for irrigation and underground residential sprinkler systems
  • Schedule 40 Pressure Fitting
  • Made in the USA
10 Pack, 1/2", Schedule 40, PVC Cap, Contractor Pack.


Friday, January 27, 2012

ANDERSON BARROWS METALS 53715-0604/5262 COUPLING INSERT FITTING 3/8" x 1/4" (PACK OF 10)

ANDERSON BARROWS METALS 53715-0604/5262 COUPLING INSERT FITTING 3/8" x 1/4" (PACK OF 10) Review



ANDERSON BARROWS METALS 53715-0604/5262 COUPLING INSERT FITTING 3/8" x 1/4" (PACK OF 10) Feature

  • Coupling .
  • Reduceing coupling
  • Nylon coupling tube
  • Bagged.
  • Size 3/8" x 1/4"
ANDERSON" COUPLING INSERT FITTING 3/8" x 1/4" Coupling . Reduceing coupling Nylon coupling tube. Bagged. Size 3/8" x 1/4"


Oatey 30755 Purple Primer For PVC And CPVC Pipe And Fittings

Oatey 30755 Purple Primer For PVC And CPVC Pipe And Fittings Review



Oatey 30755 Purple Primer For PVC And CPVC Pipe And Fittings Feature

  • Part # 30188
  • Color - Purple
  • For PVC, CPVC
A purple tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all schedules and diameters. Formulated to remove surface dirt, grease, and grime as well as soften the pipe surface to allow for a fast, secure, and permanent solvent weld. For use in areas where code calls for verification that a primer has been used. Recommended for all PVC and CPVC installations. NSF and UPC listed. Exceeds ASTM F 656.


Wednesday, January 25, 2012

Ridgid 12698 3-Inch Aluminum RapidGrip Pipe Wrench

Ridgid 12698 3-Inch Aluminum RapidGrip Pipe Wrench Review



Ridgid 12698 3-Inch Aluminum RapidGrip Pipe Wrench Feature

  • Model 18
  • All the great benefits of the heavy-duty RapidGrip
  • Ideal for overhead applications
  • Nominal size 18
  • Ridgid covers its products with a lifetime warranty against defects in material or workmanship for the life of the tool
One handed adjustment. Rapid ratcheting action. Agressive tooth design for secure grip. Thumb trigger for easy application and removal.


Monday, January 23, 2012

Charlotte PVC Side Outlet Elbow (PVC 02520 0600)

Charlotte PVC Side Outlet Elbow (PVC 02520 0600) Review



Charlotte PVC Side Outlet Elbow (PVC 02520 0600) Feature

  • Slip socket x slip socket x female pipe threaded
  • Schedule 40
  • 140 degree F. (60 degree C.) maximum operating temperature
  • Meets ASTM D-2466
  • Conforms to NSF Standard 61
Sold as each. Slip socket x slip socket x female pipe threaded. Schedule 40. 140 degree F. (60 degree C.) maximum operating temperature. Meets ASTM D-2466. Conforms to NSF Standard 61. White. 1/2" x 1/2" x 1/2". Manufacturer's number: PVC 02520 0600. Country of origin: United States. Distributed by Charlotte Pipe & Foundry.


Sunday, January 22, 2012

Schedule 40 PVC Reducer Bushing (PVC 02108 6200)

Schedule 40 PVC Reducer Bushing (PVC 02108 6200) Review



Schedule 40 PVC Reducer Bushing (PVC 02108 6200) Feature

  • Meets ASTM D-2466
  • White
Sold as each. Meets ASTM D-2466. White. . 4" x 3". Manufacturer's number: PVC 02108 6200. Country of origin: United States. Distributed by Charlotte Pipe & Foundry.


Friday, January 20, 2012

Imperial Mfg Group 3' Ci Damper Bm0241 Stove Pipe Fittings

Imperial Mfg Group 3' Ci Damper Bm0241 Stove Pipe Fittings Review



Imperial Mfg Group 3' Ci Damper Bm0241 Stove Pipe Fittings Feature

  • Imperial #BM0241 3" CI Damper
  • IMPERIAL MFG GROUP
3' Cast Iron Damper.


Thursday, January 19, 2012

Flex-Drain 53702 Flexible T / Y, Landscaping Drain Pipe Adapter

Flex-Drain 53702 Flexible T / Y, Landscaping Drain Pipe Adapter Review



Flex-Drain 53702 Flexible T / Y, Landscaping Drain Pipe Adapter Feature

  • Creates a perfect Y and T shape
  • Flexes and bends to fit most any angle
  • Exceeds all applicable ASTM Standards
  • Compatible with most traditional 3-inch and 4-inch corrugated pipe and 4-Inch PVC
  • 30-Percent higher load-bearing rating than standard corrugated pipe
Flex-drain 53702 flexible t / y, landscaping drain pipe adapter eliminate the need to use rigid wyes and tees, because it flexes to become either. Works with 3-inch and 4-inch corrugated pipe and 4-inch pvc. Flexes and bends to fit most any angle. All flex-drain products are made in america.


Tuesday, January 17, 2012

Cash Acme U3008A Shark Bite Push-Fittings Slip Coupling, 1/2-Inch

Cash Acme U3008A Shark Bite Push-Fittings Slip Coupling, 1/2-Inch Review



Cash Acme U3008A Shark Bite Push-Fittings Slip Coupling, 1/2-Inch Feature

  • The slip coupling simplifies repair by doing the job that two couplings and extra pipe used to do , this item cannot ship to CA or VT
  • One end of the coupling has a stop, allowing the other end to slide freely over the end of a pipe
  • The push-fitting can be release with a disconnect tool and slide back onto the other end of the pipe for successful leak repair
  • Easy quick push-fitting connectors CTS Copper
  • Slip couplings should only be used on Copper
Repair copper pipe easily. 1 end of coupling does not have a stop, which allows you to slide coupling on to pipe and then slide back to cover where pipe is cut out. Brass push fitting. UPC, IAPMO, and NSF 61 certified and approved. The fitting should be used with copper only and is rated at 200 F., 200 P.S.I. It is made of 1 piece DZR brass, which is a noncorrosive, low lead material. Fittings can be buried and placed behind drywall. Fittings are removable and reuseable. Product is individually bagged.


Monday, January 16, 2012

Flex-Drain 55020 Drain Pipe Coupler Adapter, Female to Female

Flex-Drain 55020 Drain Pipe Coupler Adapter, Female to Female Review



Flex-Drain 55020 Drain Pipe Coupler Adapter, Female to Female Feature

  • Female to female coupler for joining 2 cut pieces of FLEX-Drain
  • Can also be used to adapt FLEX-Drain to some wyes and tees
  • Exceeds all applicable ASTM standards
  • Compatible with most traditional 3-inch and 4-inch corrugated pipe and 4-Inch PVC
  • 30-Percent higher load-bearing rating than standard corrugated pipe
Flex-drain 55020 coupler, landscaping drain pipe adapter, female to female coupler for joining 2 cut pieces of flex-drain together. It can also be used to adapt flex-drain to some wyes and tees to improve the fit and function of the overall system all flex-drain products are made in america.


Sunday, January 15, 2012

Parker 2-2 B2HF-B Brass Barbed Connector To Male Pipe 1/8" Hose Barb x 1/8" Male NPT

Parker 2-2 B2HF-B Brass Barbed Connector To Male Pipe 1/8" Hose Barb x 1/8" Male NPT Review



Since 1924, Parker Hannifin Corporation has served the marketplace with dependable fluid power technology. Much of that expertise originates with Parkers precision-made tube fittings, which were among the first products manufactured by the company. As such, they reflect Parkers ongoing commient to excellence. With more than a half century of experience in product design, engineering and manufacturing, the Tube Fittings Division holds a leadership position few other manufacturers can claim. This leadership is further heightened and enhanced by the technology-sharing only possible in Parkers corporate family. Parker manufactures a broad line of tube fitting and adapters including the Triple-Lok fitting Ferulok fitting (flareless), Intru-lok fitting (brass flareless), EO fitting (metric flareless), EO-2 fitting (metric flareless with elastomeric seal), Seal-Lok fitting (O-ring face seal), Pipe Fittings and Adapters, JIS fittings, Hydraulic Flanges and Adapters, which are offered in a variety of port ends - NPTF, SAE Straight Thread, BSPP, BSPT, ISO and metric. This along with an extensive line of tube fabrication equipment and tube and hose clamps make up the broadest product offering in the industry.


Cash Acme U412A Shark Bite 3/4-by-3/4-by-1/2-Inch Push-Fittings Reducing Tee

Cash Acme U412A Shark Bite 3/4-by-3/4-by-1/2-Inch Push-Fittings Reducing Tee Review



Cash Acme U412A Shark Bite 3/4-by-3/4-by-1/2-Inch Push-Fittings Reducing Tee Feature

  • The Cash Acme SharkBite fittings line presents a revolutionary solution to connecting water distribution pipe , this item cannot ship to CA or VT
  • Our SharkBite Push-Fittings are the fastest, easiest way to join copper, CPVC or PEX pipe in any combination
  • With no soldering, clamps, unions or glue
  • The line includes 10 different fittings in a variety of sizes
  • Certified to 200 psi and 200-Degree Fahrenheit
Brass push fitting. UPC, IAPMO, and NSF 61 certified and approved. The fitting can be used with copper, PEX, and CPVC and is rated at 200 F., 200 PSI. It is made of 1 piece DZR brass, which is a noncorrosive, low lead material. Fittings can be buried and placed behind drywall. Fittings are removeable and reuseable. Product is individually bagged.


Wednesday, January 11, 2012

Cash Acme U514A Shark Bite Push-Fittings End Cap, 1/2-Inch

Cash Acme U514A Shark Bite Push-Fittings End Cap, 1/2-Inch Review



Cash Acme U514A Shark Bite Push-Fittings End Cap, 1/2-Inch Feature

  • The SharkBite Push-Fittings allow the user to connect pipe in seconds with relative ease , this item cannot ship to CA or VT
  • Instant push-fit connection for increased ease-of-use
  • Fittings certified to 200 PSI and 200-Degree Fahrenheit
  • Fits copper tubing and CTS CPVC and PEX
  • Integral tube liner for PEX installations
Brass push fitting. UPC, IAPMO, and NSF 61 certified and approved. The fitting can be used with copper, PEX, and CPVC, and is rated at 200 F., 200 PSI. It is made of 1 piece DZR brass, which is a noncorrosive, low lead material. Fittings can be buried and placed behind drywall. Fittings are removeable and reuseable. Product is individually bagged.


Tuesday, January 10, 2012

Cash Acme U134LFA 3/4-Inch by 3/4-Inch MNPT SharkBite Lead Free Straight Connector

Cash Acme U134LFA 3/4-Inch by 3/4-Inch MNPT SharkBite Lead Free Straight Connector Review



Cash Acme U134LFA 3/4-Inch by 3/4-Inch MNPT SharkBite Lead Free Straight Connector Feature

  • Straight connector
  • Push fittings are the fastest, easiest way to join copper, CTS, CPVC and PEX in any combination
  • No soldering or glue
  • Certified to 200 psi and 200 degree F
  • Use for new installation and repair of potable water distribution systems
Cash Acme U134LFA 3/4" X 3/4" MNPT SharkBite Lead Free Straight Connector Cash Acme U134LFA 3/4" X 3/4" MNPT SharkBite Lead Free Straight Connector Features: Straight connector Push fittings are the fastest, easiest way to join copper, CTS, CPVC and PEX in any combination No soldering or glue Certified to 200 psi and 200 F Use for new installation and repair of potable water distribution systems Lead free 3/4" x 3/4" MNPT CA/VT Compliant